Aluminum Alloy 1.0mm Flat Panel Rolling Shutter Door Commercial Lightweight Design
Product Summary
Premium 80 Type Aluminum Alloy Flat Panel Rolling Shutter Door Commercial A lightweight aluminum alloy shutter that reads as part of a designed facade, pairing 80-type 1.0mm flat-panel slats with a quiet drive for shops, offices and showrooms. Product Overview Premium 80 Type Aluminum Alloy Flat ...
Product Custom Attributes
Flat Panel Rolling Shutter Door
,Lightweight Design Rolling Shutter Door
Product Description
A lightweight aluminum alloy shutter that reads as part of a designed facade, pairing 80-type 1.0mm flat-panel slats with a quiet drive for shops, offices and showrooms.
The Premium 80 Type 1.0mm Aluminum Alloy Flat Panel Rolling Shutter Door uses 80 mm flat-panel aluminum alloy slats at 1.0 mm thickness so the curtain stays light, corrosion resistant and easy to operate while presenting a uniform, paintable facade line. Lianxin Chitai finishes each unit to a brand RAL palette and documents size and cycle life for facility managers who plan maintenance around real numbers.
Engineered and factory-finished by Lianxin Chitai, every unit balances a refined appearance with light weight, corrosion resistance and long-term serviceability.
Aluminum slats cut curtain weight for easier, quieter operation.
Alloy with powder coat suits coastal and humid sites.
Flat panels and concealed hardware give a uniform elevation line.
Nylon guide liners keep operation low-noise near offices and lobbies.
Light curtain reduces motor load and extends drive life.
Cycle rating supports planned maintenance scheduling.
Standard parameters are listed below. Custom sizes, slat thickness, and operation are available on request.
| Curtain Material | 1.0 mm aluminum alloy flat-panel slats |
|---|---|
| Slat Type | 80-type flat panel, single or double wall |
| Slat Height | 80 mm |
| Max Width | 6000 mm |
| Max Height | 6000 mm |
| Wind Resistance | Up to Class 3 (EN 13241) / 500 Pa |
| Opening Speed | 0.15 - 0.25 m/s |
| Operation | Tubular motor 220V / manual crank backup |
A clear view of the main components that make the premium aluminum shutter light, weathertight and serviceable.
Wind pressure on a wide shutter produces a distributed lateral load that the slats must carry to the guides without buckling. The 1.0 mm aluminum flat-panel profile raises stiffness at low weight, while the end locks couple adjacent slats so the curtain acts as a continuous plate rather than independent strips. Guide rails sized to the span then deliver the load to the building structure, keeping deflection within the facade tolerance while the light curtain eases motor duty.
A controlled line turns aluminum coil into a tested, branded flat-panel shutter.
Aluminum coil is roll-formed into 80 mm flat-panel slats.
Powder coat or anodize; cure and inspect color.
End locks are crimped and tested for interlock strength.
Slats linked, bottom bar and suspension shaft fitted.
Tubular motor, guides and controls assembled to spec.
Full open-close cycle and check before packing.
Where a light, clean-line aluminum shutter is the right call.
Branded storefronts that close securely and quietly.
Quiet, clean-line shutters for glass building bases.
Display-grade finish with corrosion resistance.
Aluminum withstands salt air better than bare steel.
What the site and installer must provide for a correct, light fit.
- Reveal opening measured square within +/-5 mm across width and height.
- Lintel or jamb able to take guide and curtain reactions.
- Dedicated 220V supply with isolator near the motor head.
- Clear internal space for the coiled curtain and service access.
- Reveals specified to the chosen slat and guide type.
Routine care that protects finish and extends service life.
- Wash slats and guides twice a year with mild detergent; rinse salt away on coast.
- Lubricate guide liners and shaft bearings every 6 months.
- Check end locks and bottom seal each quarter for wear or loosening.
- Test manual crank backup and safety reverse every 3 months.
- Log cycles and book motor service at the rated interval.
Common questions about premium 80-type aluminum alloy shutters.
What does 80 type 1.0mm mean?
80-type refers to the 80 mm slat profile; 1.0mm is the aluminum alloy thickness of each flat-panel slat, balancing stiffness and light weight.
Can the slats be matched to a brand color?
Yes. Slats are powder-coated or anodized to a specified RAL so the shutter matches the building facade and signage.
Does it resist corrosion near the sea?
Aluminum alloy with a quality coating resists salt corrosion far better than bare steel; we recommend more frequent washing in coastal locations.
What is the backup if power fails?
Every unit includes a manual crank override so the light curtain can be opened or closed without electricity.
How wide can a single shutter span?
Up to 6000 mm wide; larger openings use divided shutters or added support.
Is it lighter than a steel roller door?
Yes. Aluminum is much lighter, which reduces motor load and makes manual operation easier.
How long does the motor last?
The tubular motor is rated for tens of thousands of cycles; we log cycles and service at the rated interval.
Can I integrate access control?
Yes. The motor accepts remote, keypad, loop or building-management triggers through a standard control interface.
What lead time should I expect?
Standard colors and sizes typically ship within a few weeks; custom RAL and oversize units are quoted per order.
Do you provide installation drawings?
Lianxin Chitai supplies elevation, fixing and load drawings so the installer can prepare the reveal correctly.
Tell us your opening size, wind class and operation need. We return a tailored proposal with lead time.
Email sales@example.comContact Our Experts And Get A Free Consultation!
Our mission is to offer "High Quality" & "Good Service" & "Fast Delivery" to help our clients to gain more profits.
